Sliding flyscreen door repair

Fix a sliding flyscreen door that sticks, jumps the track or won't latch, choose the right rollers, remesh a door screen and see what it costs.

Screwdriver turning the roller adjusting screw at the bottom corner of a cream sliding flyscreen door in its track

Most sliding flyscreen door problems come down to three things: a dirty track, worn or badly set rollers, or a frame that has gone out of square. Clean the track first, then adjust or replace the rollers. Only once the door runs well should you worry about the mesh.

Work out what’s wrong first

What the door does Likely cause First thing to try
Hard to slide, grinds or judders Grit in the bottom track, or a cracked or flat-spotted wheel Clean the track, then check each wheel spins freely
Drags on the bottom of the frame Rollers worn down or wound too low Raise the rollers with the adjusting screw
Jumps off the track Rollers too low, missing top guide, bent frame or dented track Raise the rollers, check the top guides
Won’t latch or lock Door sitting at the wrong height or out of square Adjust roller height until the latch meets the keeper
Gap at the side, bugs getting in Worn pile (bug strip) or door not square Replace the pile, square the door with the rollers
Mesh baggy, torn or pushed out Old or damaged mesh, loose spline Remesh the door

Clean the track

  1. Slide the door to one end and vacuum the bottom track, then do the other end.
  2. Scrub the track with a stiff brush and warm soapy water, getting into the corners where sand and leaves pack in.
  3. Dry it and check the rail the wheels run on for dents, flat spots or a rail worn thin.
  4. If you lubricate, use a little dry silicone spray. Oil and grease tend to hold grit.

Hand scrubbing sand and leaves out of a sliding flyscreen door track with a brush and soapy water

Adjust the rollers

Most sliding fly doors have two adjustable rollers at the bottom, one near each corner, with a small adjusting screw in the bottom rail or on the side edge near the bottom. Doors vary, so this is general practice rather than one maker’s instructions.

  1. Find the adjusting screw at each bottom corner.
  2. Turn it a quarter turn at a time. One direction raises that corner of the door, the other lowers it.
  3. Raise both rollers evenly until the bottom of the frame clears the track and the door slides freely.
  4. Check the gap down the closing side. If the door is higher at one end, adjust that end until the edge sits parallel with the jamb.
  5. Close the door and check the latch lines up with its keeper.

Don’t wind the rollers up so far that the top of the door is jammed into the top track. You want it held in both tracks with a little play.

Replace worn rollers

A wheel that is cracked, wobbly, seized or worn flat needs replacing.

Get the door out

Wind both adjusting screws until the bottom rollers retract and the door drops. Lift the door up into the top track and swing the bottom out towards you. A fly door is light, but it’s tall and catches the wind, so get a second person on a balcony or a gusty day. If your door has a security lock or steel mesh, see the security door repairs guide instead.

Identify the part

Sliding screen door rollers are not one standard size. The wheel, the carriage (the housing it sits in), the way it fixes to the frame and the adjuster position all vary by door maker.

  • Wheel only or whole carriage. If the housing is cracked or the adjuster is stripped, buy the full carriage and roller, not just a wheel.
  • Wheel size and profile. Bunnings stocks Rolltrak concave wheels in several diameters, including 24 and 32 mm.
  • How it’s fixed. Many are held by a screw, some clip in, and some are riveted, which means drilling the rivet out.
  • Fly door or security door. Security doors use heavier-duty rollers, so don’t put a light fly door carriage in a security door.

Take the old roller to the store. Some Bunnings pages for Rolltrak carriages include a 1:1 scale PDF you can print and hold your old part against. Screen hardware makers such as Doric also sell carriages, corner stakes with rollers built in and hanger brackets, and list a phone line for help choosing rollers.

Worn, grimy sliding screen door roller carriage beside a new white nylon carriage and roller, a screwdriver nearby

What rollers cost

Checked on the Bunnings and Doric websites in November 2026 (indicative, prices change):

Part About
Replacement wheel only (Rolltrak) $6.50 to $20 each
Carriage and roller (Rolltrak, single or 2 pack) $10.50 to $27
Doric fly door carriages, corner stakes and hanger brackets $3 to $27 each
Sliding screen door lock (Rolltrak, non-keyed to keyed) $39 to $69

Check whether a listing is a single roller or a pair. Most fly doors need two bottom rollers.

Fit them

  1. Undo the screw holding the old carriage, or drill out the rivet.
  2. Slide the old carriage out and push the new one in the same way round.
  3. Refit the screw.
  4. Wind the new rollers fully up, refit the door top first, then wind them down onto the track.
  5. Adjust as in the section above.

Fix a door that jumps the track

When the rollers are set right and the door still pops out, check these:

  • Top guides. These small plastic blocks on top of the frame keep it in the top track. Replace them if they’ve snapped off or worn down.
  • Dented bottom track. A small dent can sometimes be eased back with pliers and a block of wood. A rail worn or squashed along its length can take a stainless capping track that sits over the old rail; screen hardware suppliers sell these in different profiles. Measure your rail first, and expect to readjust the rollers afterwards.
  • Bent frame. A bowed or twisted door won’t sit in both tracks at once. See below.

If the house’s own track is badly damaged, call a screen business or an aluminium window and door repairer.

Fix the latch and the bug strip

A latch that won’t catch is usually a height problem: adjust the rollers until it meets its keeper. If the latch itself is broken, take the old one to the store so the fixing holes line up.

The bug strip is the brush pile along the edge where the screen meets the glass door. Once it’s flattened or torn, insects walk through the gap. Pile comes in different backing widths and pile heights, so take a length of the old one with you. It slides out of its groove and the new one slides in.

Remesh a sliding screen door

Remeshing a door is the same job as a window screen, covered step by step in our guide to replacing flyscreen mesh. Doors bring a few extra problems.

Stop the frame bowing

A door screen has long sides, often over 2 m, and it’s common for the mesh tension to pull the long sides inwards as you roll in the spline. The door ends up waisted and won’t sit in the tracks or close against the jamb. These steps are common practice to avoid that:

  1. Lay the door flat on a table or two trestles.
  2. Brace the frame: clamp the long sides to the bench, or wedge a timber batten across the middle.
  3. If the door has a midrail, do the top and bottom panels as separate jobs.
  4. Work around the frame evenly, doing opposite sides in turn, and don’t stretch the mesh drum tight.
  5. Before trimming, sight down the long sides to check they’re still straight.

What you need

  • Mesh for the panel plus about 50 mm spare all round. A full-height panel may be longer than a 2 m pack.
  • New spline in the right size
  • A spline roller and a sharp knife
  • A flat-blade screwdriver to lift the old spline
  • Clamps or a timber batten for bracing
  • Gloves if you’re using aluminium or stainless mesh, which has sharp cut edges

Pet mesh on doors

Doors take knocks windows never see: dogs jumping up, cats climbing, kids walking into them. Pet mesh is a much heavier weave that copes far better than standard fibreglass, but it’s thicker, so test-fit your spline in the channel with the new mesh before you start. Bunnings listed pet mesh at about $35 for 1220 mm x 2 m (checked November 2026). More in our pet mesh guide.

What a professional repair costs

Prices vary by city, door size and how many screens are done in one visit. Published examples checked in November 2026:

  • A Sydney Northern Beaches handyman business (Handy Work) lists about $130 to $200 to remesh the first sliding door and about $110 to $130 for each extra door.
  • A Melbourne business (Danny’s Home Services) lists door remeshing from $99 each, with a minimum of four screens.
  • For a whole new door, one screen business (Screen and Blind Master) puts a standard sliding flyscreen door of about 900 x 2,100 mm at around $480 or more with a magnetic latch, and from around $550 with a single point lock.

Roller jobs are usually priced as a call-out plus parts. Our cost calculator gives estimates for remeshing and replacing door screens.

When the door is beyond repair

Replace rather than repair when:

  • the frame is twisted or badly bent, so it won’t sit in both tracks even with the rollers adjusted
  • the corner joints have split or the corner stakes are broken
  • the mesh, rollers and latch are all worn at once
  • the rollers for that frame are no longer made and nothing else fits

New sliding flyscreen doors are usually made to measure by a screen business, because they have to fit your tracks. Our flyscreen doors guide compares hinged, sliding and security screen doors with costs.

When to get someone in

Get a screen business in if the door is on an upper-floor balcony where a dropped door could go over the rail, if it’s a security door, if the house’s track is damaged, or if you can’t identify the rollers. They can often remesh, re-roller and adjust a door in one visit.

Find a local screen business or get a quote for your door.

Questions

Why does my sliding flyscreen door keep coming off the track?

Usually the bottom rollers are set too low, a top guide is missing or worn, or the frame has bowed so it no longer sits square in the tracks. Clean the track, raise the rollers a little and check the top guides before buying anything.

Can I replace sliding screen door rollers myself?

Yes, on most fly doors it is a screwdriver job once the door is out. The hard part is matching the part, so take the old roller or carriage to the store with you.

How much does it cost to fix a sliding screen door?

Rollers from Bunnings were about $10 to $27 each in November 2026, so a roller job is often under $50 in parts. Published prices from screen businesses for remeshing a sliding door were about $99 to $200, checked November 2026.

Should I use pet mesh on a sliding screen door?

If you have a dog or cat that pushes on the door, or kids who walk into it, pet mesh is worth considering. It is much tougher than standard fibreglass but heavier, darker and more expensive.

Is it worth fixing an old sliding flyscreen door?

If the frame is straight and the corners are tight, usually yes, because rollers and mesh are cheap compared with a new door. If the frame is twisted, the corners have split or the parts are no longer made, a new door is usually the better buy.

Find a flyscreen repairer near you

Prefer someone else to do it? Search your suburb, or send a free quote request.